Off-Grid Pump House

I am so behind in a lot of my posts.  Sorry.

A lot has been happening around here.

Last March I started telling you about the pump house we were building.

You may recall that framing the walls was next on the agenda.  If you havent seen that previous post, you can catch up by clicking HERE.

Since we drilled the holes in the sill boards for the J-bolts and PVC conduit pipes, then set everything in place, tightening the bolts tight, the concrete was able to cure with everything in it’s proper place.

We decided to re-use the lumber that we used for framing the concrete slab (reduce, reuse, recycle!), so I spent some time scraping off the cement from the boards.

We began framing one wall at a time, which was definitely a two person job.  Sometimes I needed three arms to hold everything up while dear hubby Ray screwed it into place, but after a lot of groaning and a few colorful words, we eventually got the walls up.  As mentioned in the first post about this pump house, we used 2 x 6 lumber (2 x 4 in a few spots for bracing) which fits nicely with the 6″ wide concrete block, and also so that in the future we can super insulate the walls and ceiling.  

Once the walls were in place, we installed a window.  We went to Habitat for Humanity’s Re-Store to purchase a few items for this project.  We got the Marvin window for about $35 and hinges for the door for $1 each!  I love going to these Re-Stores and spending an hour or so just looking around, because you never know what you might find!  We have been to several and each one is different, which makes the shopping adventure just that much better!

We needed to put a window into the pump house not only for the natural light, but also in case we need to pull the pump out of the well.  The window was positioned right in front of the well head, and it’s big enough to slide open and pull the pump through.

Next came the roof.  We bought these metal “hangers” from the big box store to make it easier to secure the rafters to the top plate of the framing.  They worked great!  When we (meaning me) first put them on, we got them upside down.  Oops!  Ray corrected my mistake.  🙂

Then we added a bit more structure to the gable ends and jack studs horizontally between the regular studs, to give the building more structure and strength. On the front side (the picture to the left is showing the back side) we also installed a vent. Eventually we plan to install a solar panel on the roof to provide a task light on the inside and a motion detector light outside, and also as a trickle charge to batteries that we can use for pumping water on cloudy days.  We have decided to leave the power to the pump separate from the power to the house because that system is already in place and running.  Ray has all that stuff worked out and I am sure glad he does, because when it comes to anything electrical (watt?  amp who? voltage where?), I am the consummate dummy!  But that’s okay because it just makes him the yang to my yin!  After 41 years of marriage, this has worked well.

So… I just nod and smile when he is telling me about all of that “stuff”.

Then the rafters went up.  Holy canolli, what a job!  They were heavy and cumbersome and we decided to put them up on a windy day.  Why would we do something so silly? Because rain was in the forecast and we wanted to get the roof on ASAP!

Now it’s actually looking like a building!  Wahoo!  The hardest part is done… right?

Well, No.

For us, the hardest part was the plywood and metal roofing.  Why?  Because the plywood is heavy (really heavy), the metal roofing is sharp, and we are both just a little nervous about heights! :O

It was a bit difficult getting the plywood exactly centered and leveled on the rafters because, unfortunately, a few of the rafters were just a bit warped and twisted. And we aren’t professional contractors. And did I mention those suckers are heavy? Oh well. You really can’t see that from the outside, so we’re good.

Just don’t look too close…

Our next task was to wrap the house and install the siding.  Since we live in an area that is prone to wildfires, we try to use fire resistant products whenever possible.  We decided to use the James Hardie Planks, just like we did on the tool shed (turned into our little cottage bunkhouse), with the James Hardie 4×8 sheets on the gable ends, for a little bit of interest. This product is fairly noncombustable as it is a cement based product.  The truth is that ANYTHING can burn… even concrete, but every little bit of prevention helps in a wildfire situation! The trim was also made from this product. The siding took the longest time to do – several days – but I think it turned out well!  We also used the Hardi Planks to close up the soffits.  Closed soffits are also an important component of a structure in a wildfire prone area.  If no sparks can get into the attic, it is less likely that the building will burn!  One thing I will say about using the James Hardie products is that they are NASTY when you cut them!  We learned from experience the first time we used this product.  It is imperative that safety goggles (the kind that completely enclose your eyes) and breathing masks be used, otherwise your snot turns to concrete marbles and your eyes will weep rocks for days!


The door was our final piece of construction.  When we were planning how big to make this building, we knew that we had to make the door big enough to be able to remove and/or replace the water storage tank.  But we also knew that we didn’t want a door to be that big, because it would tend to sag and warp.  So, we decided to make a double door system where only one door is used and the other, while useable when necessary, would usually be pinned shut with a bolt going through the door and into the concrete on the bottom.  We bought the hinges at the Re-Store and the handle and lock system at the big box store.  Once the doors were constructed, we trimmed them out with the Hardi Board to match the gables and… voila!

I couldn’t wait to hang my sun on the side of the building!

Now, all we have to do is paint!

This is where the party is:Thank Goodness It’s MondayClever Chicks Blog HopGrand SocialMix It Up MondayCreate, Link, Inspire;  Amaze Me Monday,  Homemaking MondaysShow & Share TuesdayThe Gathering SpotBrag About ItTuesdays with a TwistThe ScoopTwo Cup Tuesday;  Inspire Me TuesdaysTuesdays at Our Home;  Party In Your PJ’s;  Show Me YoursMake, Bake and Create;   Wined Down Wednesday;  Fluster’s Creative Muster;  Homestead Blog HopWow Us Wednesday;  Wonderful Wednesday;  Waste Less WednesdayAIM LinkyOur Simple Homestead; Share Your Cup Thursday;  Home and Garden Thursday;  The Handmade HangoutThink Tank Thursday;  Homemaking Party;  This Is How We RollNo Rules Weekend Party;  Friendship Friday;  Family Fun FridayFriday’s Five FeaturesAwesome Life Friday;  Home MattersTraffic Jam WeekendSaturday Sparks;  Dare to ShareScraptastic SaturdayShare It One More TimeHappiness is HomemadeAnything Goes Pink SaturdaySimple SaturdaysThat DIY Party;  DIY Sunday ShowcaseSnickerdoodle Sunday;   Best of the BlogosphereSmall Victories Sunday

Related Posts Plugin for WordPress, Blogger...